In the quality regret survey, there were relatively more regrets in the change of the unit type, accounting for 28.9%, and the floor and floor tiles also accounted for 28.3%, while the regret for the wall paint, wallpaper and tile accounted for 24.6%, bathroom The regret of sanitary ware and cabinets accounted for 22.5%, and the lighting arrangement also accounted for nearly 20%. The proportion of various quality regrets was even. In the survey, we found that more than half of the voters believe that the details are most likely to appear regrettable. The more detailed the more you can see the quality of the construction, the designer's ability and the overall control of the decoration company. The regret for quality is usually caused by negligence in construction, such as wall cracks, uneven yin and yang angles, and so on. Some regrets can be made up the day after tomorrow, and some regrets are incurable.
>>>Recommendation: Decoration regrets and matters needing attention--Bathroom
[regrets one] The toilet slope is too small
The bathroom floor should be tilted toward the floor drain. However, if the slope is too large, it looks like the effect is not good. If the slope is too small, if there is too much water, it will go outside. The slow drainage will cause the sewage to precipitate during the drainage process, leading to a smelly smell in the bathroom.
Reason for regret:
First, it may be considered that large slopes will affect the appearance of the ground, construction workers will slow down the slope of the toilet; second, the floor tiles are too large, so that the slope is not good to adjust.
Afterwards Zhuge:
If the groundwork has been completed, only to find the slope is too small, it is recommended to select the shower screen, concentrate the water in the shower area, do not flow to other areas; you can hang a shower curtain above the bathtub, blocking the water splash.
[pity two] woodworking rough
Many people prefer to make carpenters to be a bar, wardrobe, etc., but after doing a good job, they regret that they are very different from the finished products sold on the market. They are not rough surfaces, or the lines are not straight.
Reason for regret:
It's best not to make live on the spot. The finished product can be customized according to the size of the home. The on-site production process can not reach, and it may not be environmental protection.
Afterwards Zhuge:
Inside the cabinet, you can polish it with fine sandpaper and then apply varnish. The wooden door can be polished by the workers and then refurbished.
[pity three] Bathroom cabinets from the skin
Bathroom steam is large, usually with more water, often feel wet. Wooden cabinets in the bathroom, under the door frame or baseboard, will mold after a period of time.
Reason for regret:
This may be just a good decoration, the outer wall of the bathroom is not completely dry, resulting in dampness; it may also be the water inside the bathroom wall to seep out of the water pipe, causing the wall to return to the tide; if the time is very long cabinet with mildew may be the bathroom Usually used too much, caused by too much fog.
Afterwards Zhuge:
The bathroom is too humid, may be because of poor ventilation, in order to alleviate this problem, the door can be replaced with a bathroom-specific door, do wet and dry partitions, install powerful exhaust fans and so on.
ã€Surprisingly four】 Floor arching
The floor appears concave or protruding phenomenon, some tilted up in the four corners, the middle depression;
Reason for regret:
The main reason is that the ground is moist, or because the wooden floor expands after being exposed to moisture, due to the anisotropy of the wood, the local stress of the board is uneven and arches.
Afterwards Zhuge:
It is possible to place furniture on the deformed part of the arching. For example, in the middle of the living room, you can use a coffee table, a stool, etc., and wait until the contraction process of the floor is over.
[Pity 5] There is a crack in the wall that has just been completed
Walls are subject to various cracks due to seasons, construction, construction, etc., especially after the wall of thermal expansion and contraction tests throughout the year, cracks are more likely to appear.
Reason for regret:
One is the cause of wall cracks due to the construction itself; the second is that the decoration team cut corners and materials, and the mixed mortar used for the plastering layer is not proportioned, or the wall surface is cracked without using plaster to level the wall surface.
Afterwards Zhuge:
The appearance of individual cracks is understandable. After all, the walls are also affected by climate or architecture.
If you're not looking right, except for reprocessing the walls, a small area can be covered with the now popular wall stickers and a large area of ​​available wallpaper.
[Sad 6] Loose tiles on the riser
Tiles often appear loosely and empty at the place where the tube is installed. If the decoration is not in place, tiles may fall or crack.
Reason for regret:
In order to save money, the decoration team used a wooden keel to stand up the pipe, and there was no anti-corrosion and waterproof coating. Tiles were not easily glued to the wooden keel, and the wood was damp, causing the tiles to loosen and fall off.
Afterwards Zhuge:
Bao Liguan applies light steel keel and cement board, and must apply waterproof and anti-corrosive paint. Tiles on concrete boards must be hung with wire mesh, otherwise it is easy to fall off. At the same time, the hanging net should be connected to the wall more than 5 cm, and the wall and the cement board should be integrated. For a good decoration and this phenomenon, we must do it again, otherwise it will affect the future use.
Experience on Cement Coatings Wallpapers Decoration Design Decoration Decoration Decoration Company Good Decoration Living Room Floor Tiles Cupboard Doors Large Wardrobe Cabinets Cabinet Doors Bathroom Tiles Bathroom Doors Bathroom Doors Bathroom Sizes Bathrooms Bathrooms Bathroom Bathrooms Bathroom Tiles Floor Tiles Ceramic Tiles
Professional OEM for Audio Electronics such like amplifier, DAC, equalizer. Our team had OEM experience for Norway high-end audio brand and can guarantee with high quality. Low volume is also one restriction when looking for good audio OEM. We are able to help you with low volume like 100 or 250 units per lot. With both AOI and manually visual inspection for the PCB to ensure each solder spot is well soldered and make sure the structure is balance which is important for audio device.
MPI have two division, electronics design & assembly house and metal stamping & CNC chop.We can provide OEM Sheet Metal Stamping Service.OEM CNC Machining Service.ODM Power Electronics Design and Assembly.ODM LED Driver.ODM Security AC/DC Power Supply.ODM Access Control Power Supply and so on.
In Electronics shop we provide our professional skills on power electronics design and manufacture. From A to Z, we can help you translate your idea into real products.
Our Metal shop provide professional stamping service which include creating mold, stamping and surface treatment. The implementation of CNC machine provide high precision machining parts and machining service to our customer.
Over 20 years experience on doing business with US and EU customers. We can understand what you need and what you concern.
Audio DAC,OEM Audio,Bluetooth DAC Amp,Audio Power Amplifier
Master Prosperous Industrial Co.Ltd. , https://www.mpigroup-taiwan.com