One: Electrician Series
In home decoration, electric construction seems to live a lot on the surface, but many potential problems leave many hidden dangers for future life. The common problems are: short circuit of the distribution line, weak television signal, and interference from telephone reception.
There is a problem:
1, improper wiring
The main problem is that there are too many line connectors and the connectors are handled improperly. Some lines are too long. Some joints will be produced during the electrician's operation. However, due to technical limitations of some of the construction team's electricians, the wiring, insulation, and moisture-proof treatment of joints are not good, and disconnection, short circuit, etc. will occur.
2, cut corners
In order to reduce costs and cut corners, there is no casing for the hidden wiring.
3, destroyed
The well-established route was damaged by subsequent construction. If the wall line is interrupted by an electric hammer and the floor is paved, the air nail gun penetrates the PVC pipe or sheath wire.
4, overload work
The distribution line does not take into account the different rated currents of the wires of different specifications. The "small horse-drawn cart" causes the line itself to be overloaded for a long time.
5, the same line
Different lines go the same line. If the television antenna, the telephone line and the distribution line are threaded into the same casing, the reception of the television and the telephone is disturbed.
II: Plumbing series
After you move into your new home, you may find water-related quality problems. Such as leaking water pipes, odors in wash basins and vegetable sinks, small bathtub showers, and inconvenience in the use of sanitary ware.
There is a problem:
1, leaking water pipes
Assuming there are no quality problems with the water pipes and the pipes themselves, both the cold water pipes and the hot water pipes may leak. Cold water pipe leakage is generally sealed when the water pipe and pipe fittings are not connected; hot water pipe leakage is not done in addition to the seal, but also may be improper selection of sealing materials.
2, the reason for the small water flow
During the construction, in order to connect the entire line, a thread should be put on the sawed water pipe. If the thread length is too long, when the pipe is screwed into the pipe fitting (such as elbow) too deep, the cross section of the water flow will become smaller and the water flow will also decrease. It's small.
3, hose burst
The serpentine hoses are mostly used to connect pipes from plumbing to sanitary fixtures. If the hose is of poor quality or the hose is tightened when the plumber installs it, the hose will burst when it is not used for a long time.
4, toilet overflow when overflowing
When the toilet is installed, the groove of the base is not sealed with an oil filler, and when flushing, the sewage overflows from the gap between the base and the ground.
5, wash basin water back odor
In the renovated bathroom, the position of the wash basin often shifts to the wrong place with the water entrance, and it is often difficult to directly use the wash pipe when the wash basin is bought. The installation workers are trying to save time and do not generally do S-bends, resulting in the direct passage of the washbasin and the sewer, and the odor returns from the sewer.
Standardized construction, strict acceptance, so as to effectively ensure the quality of hydropower projects in order to provide security for future home life. So don't be sloppy when it comes to acceptance of hydropower!
Water and electricity acceptance construction acceptance TV TV decoration toilet home decoration bathroom leak
Cutting consumables
Selecting the right cutting wheel will help to ensure fast cutting, no structural changes to the cutting wheel or sample due to overheating or deformation, and improve cutting wheel wear, thereby helping to reduce costs. All of our cutting wheels, blades, additives and other cutting consumables have been developed specifically for metallographic cutting, including state-of-the-art abrasive wet cutting technology and precision cutting.
No structural change
Does not overheat
There is no deformation
There are various cutting wheels to choose from, suitable for all types of material preparation.
Cutting Consumables,Metallography Consumables,Laser Cutting Consumables,Wire Edm Consumables
TROJAN (Suzhou) Technology Co., Ltd. , https://www.trojanmaterials.com