Hard hat impact resistance tester sensor and amplifier installation and disassembly article from Qingdao Zhongbang Instrument Co., Ltd. Technical Department 1, helmet impact resistance test machine sensor installation 1), connect the sensor input signal line, clockwise rotation, until the spin Tightly.
Note: If the force value is not displayed during the test, the sensor may not be connected properly. At this point, you can remove the sensor signal cable, scrub the connector with alcohol, and then reinstall it.
2) Put the connected sensor lightly into the base slot.
3) Put the head mold connector and thick gasket in order, and screw on the Allen screw. Be careful not to tighten the screws at this time.
4) Put the head mold vertically, turn the head mold, and tighten the hexagon socket screw while ensuring that the head mold freely rotates. If the head mold does not rotate smoothly, loosen the Allen screw and adjust it again.
2. Disassembly of the helmet impact resistance tester sensor 1) Pull the head mold vertically upwards and place it outside the tester.
2) Remove the four socket head cap screws on the fixed head mold connector, and remove the fixed head mold connector and the underside gasket.
3) Gently remove the sensor from the base slot.
4) Rotate the connection counterclockwise to remove the input signal line from the sensor.
5) Take out the sensor and complete the disassembly.
3. Installation of impact helmet impact tester amplifier 1) Fix the amplifier bracket firmly 2) Connect the sensor signal input line to the input of the amplifier (clockwise tightening)
3) Insert the power plug into the power socket of the amplifier 4) Connect the output signal cable to the output of the amplifier (turn the plug clockwise until it locks)
Note: After the amplifier is installed, be sure to turn the amplifier on and off. 4. Remove the helmet impact resistance tester amplifier 1) Remove the top case 2) Remove the amplifier power plug 3) Remove the sensor connection at the output Line (counterclockwise rotation)
4) Remove the amplifier fixing bracket and disassemble it. This article is an article of Qingdao Zhongbang Instrument Co., Ltd. If you need to reprint it, be sure to add the source of the description. Reproduce the misuse without permission, and bear responsibility!
Note: If the force value is not displayed during the test, the sensor may not be connected properly. At this point, you can remove the sensor signal cable, scrub the connector with alcohol, and then reinstall it.
2) Put the connected sensor lightly into the base slot.
3) Put the head mold connector and thick gasket in order, and screw on the Allen screw. Be careful not to tighten the screws at this time.
4) Put the head mold vertically, turn the head mold, and tighten the hexagon socket screw while ensuring that the head mold freely rotates. If the head mold does not rotate smoothly, loosen the Allen screw and adjust it again.
2. Disassembly of the helmet impact resistance tester sensor 1) Pull the head mold vertically upwards and place it outside the tester.
2) Remove the four socket head cap screws on the fixed head mold connector, and remove the fixed head mold connector and the underside gasket.
3) Gently remove the sensor from the base slot.
4) Rotate the connection counterclockwise to remove the input signal line from the sensor.
5) Take out the sensor and complete the disassembly.
3. Installation of impact helmet impact tester amplifier 1) Fix the amplifier bracket firmly 2) Connect the sensor signal input line to the input of the amplifier (clockwise tightening)
3) Insert the power plug into the power socket of the amplifier 4) Connect the output signal cable to the output of the amplifier (turn the plug clockwise until it locks)
Note: After the amplifier is installed, be sure to turn the amplifier on and off. 4. Remove the helmet impact resistance tester amplifier 1) Remove the top case 2) Remove the amplifier power plug 3) Remove the sensor connection at the output Line (counterclockwise rotation)
4) Remove the amplifier fixing bracket and disassemble it. This article is an article of Qingdao Zhongbang Instrument Co., Ltd. If you need to reprint it, be sure to add the source of the description. Reproduce the misuse without permission, and bear responsibility!
A kids Ceiling Lamp is a type of lighting fixture that is specifically designed for children's rooms. It usually features a fun and playful design, such as cartoon characters, animals, or shapes that appeal to kids. These lamps are often made with child-friendly materials and are designed to emit a soft and gentle light to create a cozy and comforting atmosphere in the room. Some kids ceiling lamps also come with additional features like adjustable brightness, color-changing lights, or built-in night lights.
Kids Ceiling Lamp ,Kids Lamp,Children Lamp,Children Lighting
Zhongshan Seekyo Lighting CO., Ltd. , https://www.seekyomodernlamp.com