1, open the suction grille in the device, hold down the buttons on both sides and gently pull down;
2. Pull the hook on the air filter and pull it out diagonally.
3, use a vacuum cleaner to remove the dust, or rinse with warm water;
4, if you encounter too much dust, then you can use a soft-bristled brush plus neutral detergent for cleaning, clean and dry the water after drying, placed in the shade to dry;
5, do not use hot water above 50 °C for cleaning, so as to avoid the phenomenon of equipment discoloration or deformation, and do not dry on the fire;
6, after the completion of cleaning must be equipment and fashion, the installation of the device hanging on the upper part of the suction grille protruding, and then fixed on the suction grille, the suction grille on the back of the handle slowly slide inward Until the entire device is pushed into the grille;
7. The final step is to close the suction grille. This is exactly the opposite of the first step. Press and hold the filter signal reset button on the control panel. The cleaning reminder will disappear.
8, in addition to remind everyone, if the initial effect of the filter used in the environment too much dust, then the number of cleaning should be subject to increase, usually six months is appropriate.
Primary filter cleaning procedure
1 Objective: To establish a standard operating procedure for the initial purification of air purification systems.
2 Scope of application: It is applicable to the preliminary filter cleaning of air purification system.
3 Responsible person: Operator of air-conditioning room.
The return air filter is cleaned once a week, the new tuyere filter is cleaned once a month, the primary filter is cleaned once a month [1], and the medium efficiency filter is cleaned once a season.
Detergent solution: Dilute an appropriate amount of detergent or detergent with purified water and dilute it to a suitable concentration, stir well.
Initial filter cleaning method:
1 First cut off the power supply of the air purification system to stop the fan operation, open the access door of the junior-intermediate filter, and loosen the four fixed wire pressure springs of the filter; gently remove the bag filter that needs to be replaced and replace the plastic filter. Bags are sent to the clean room.
2 First, turn the filter surface of the primary and middle efficiency filter outwards, gently tap the filter with a wooden stick to remove the floating surface of the filter surface, then soak in the detergent solution for 15 minutes, use a pressure method to wash away the dust and Dirt, rinsed with tap water, and slightly removed some of the water by pressing.
3 The washed filter is sent to a general area washing machine to dry the moisture, and then dried at a low temperature of 60° C. or lower.
4 The filter should be inspected for damage after cleaning. If the filter surface is empty or loose, a new filter should be updated.
4 The return air and fresh air filter are cleaned with detergent and rinsed with tap water.
5 Use a damp cloth to clean the inside of the air conditioning unit. In particular, clean the filter frame and related parts to ensure that the dust that has been scattered during the replacement is clean.
6 Lightly load the filter and press it with the compression spring.
7 Inspect each filter in general to ensure that it is fixed and reliable.
Lathe parts processing refers to the manufacturing process of creating custom metal parts on a lathe machine. Lathe machine is a versatile tool used in various industries including automotive, aerospace, and electronics. Lathe parts processing involves using a lathe machine to cut, shape, and form metal parts according to the required specifications.
The process of lathe parts processing involves several steps. First, the metal material is selected based on the specific requirements of the part to be produced. Once the material is chosen, it is loaded onto the lathe machine, and the cutting process begins. The lathe machine is programmed to move the material towards the cutting tool, which removes material to create the desired shape and dimensions.
Lathe parts processing can produce a wide range of parts in varying shapes and sizes. Lathe machines use a variety of cutting tools, including drills, taps, and reamers, to produce parts according to the required specifications. Additionally, the lathe can produce components with varying levels of complexity, from simple cylindrical shapes to more complex shapes with intricate details.
One of the significant advantages of lathe parts processing is its ability to produce large quantities of parts with high accuracy and consistency. Lathe machines can be programmed to produce the same part repeatedly, ensuring consistency and quality control. This is especially beneficial in industries where a large volume of identical parts is required.
Another advantage of lathe parts processing is its versatility. Lathe machines can be used to produce parts from a variety of materials, including metals, plastics, and composites. Additionally, lathe machines can produce parts with various finishes, such as polished or textured surfaces.
In conclusion, lathe parts processing is an essential manufacturing process in various industries. It offers the ability to produce customized parts with high accuracy and consistency, which is vital in industries where quality and precision are critical. With the ability to produce parts in large quantities, lathe parts processing offers a powerful solution for a wide range of applications.
Turning Operation On Lathe Machine,Grooving Operation On Lathe Machine,Reaming Operation On Lathe Machine,Drilling Operation In Lathe Machine
Lizhi Precision Manufacturing Technology Co.,Ltd , https://www.lizhipartsmfg.com