Dongguan Jiujia Anticorrosive Equipment Co., Ltd.
1. Polyethylene (PE) plastic cans are formed by a rotational molding process.
Dongguan Jiujia Plastic Anti-corrosion Storage Tank is made of Rotomolding Special Material - Linear Low Density Polyethylene (LLDPE) or Linear Medium Density Polyethylene (LMDPE). It can hold most of the inorganic acids, alkalis, salts and many inorganic substances at room temperature.
2. The material used has a minimum softening point of 108 ° C and a maximum breaking point of -70 ° C, so it can generally be used for liquids with a temperature of -40 ° C to 60 ° C. If the temperature of the liquid is higher than 60 °C, a metal reinforcing sleeve should be arranged to prevent the tank from softening and deforming. If the tank is used for chemical reaction or dilution, the corresponding experiment should be carried out in advance to determine the maximum temperature of the reaction or dilution.
3. When you are not sure whether a substance can be contained, please refer to the Table of Chemical Properties of Polyethylene.
4. Install the basic requirements of the tank and be able to withstand the corresponding pressure, such as steel structure, the gap should not be too large, and should be covered with wood or iron.
5. When the storage tank is storing chemicals, there should be a good drainage ditch and dilution device around the site.
6. Since the tank is inevitably formed into a spherical crown when it is formed in the bottom of the tank, the foundation should be made into a spherical crown similar to the shape of the bottom. It is recommended to use a sand-like crown corresponding to the bottom of the tank on a horizontal basis. ).
7. Large-scale storage tanks should be safe when installing. Try to use cranes. Please contact us if you don't know the method.
8. When the plastic joint is tightened at the factory, the joint may loosen during transportation, loading and unloading. Therefore, the sealability of the joint should be checked before use. The liquid can be added to the joint to observe whether it leaks. Liquid storage tanks containing chemicals are best tested for leaks in water to prevent substantial losses.
9. The pipe connected to the lower joint or flange of the tank should be perpendicular to the wall of the tank. It is best to use a soft connection to avoid the uneven expansion of the upper and lower walls of the tank after the liquid is filled, resulting in leakage of the joint connection and damage to the joint and Bucket.
10. When the inlet port is higher from the bottom of the tank, the inlet port should be bent toward the tank wall to allow the incoming liquid to fall along the tank wall to reduce the impact on the bottom.
11. When installing a heavier accessory such as a mixer, or if the person has to work on the top of the tank and the top of the tank cannot bear the weight of the person, please make another shelf or ladder and pay attention to the safety of the work.
12. In the case where the liquid level cannot be controlled, an overflow port should be installed to prevent the liquid from overflowing from the manhole and cause unnecessary damage.
13. When the liquid inlet and discharge flow are large, the exhaust pipe of the corresponding flow rate should be installed.
14. Please contact our company again when changing the liquid.
15 If the tank is to be moved, use the steel plate to make the bottom and add the wheel underneath. It is best not to move.
Source Dongguan Jiujia Anticorrosive Equipment Co., Ltd. specializes in producing anti-corrosion plastic storage tanks, more plastic storage tanks information http://
Http://news.chinawj.com.cn Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn
1. Polyethylene (PE) plastic cans are formed by a rotational molding process.
Dongguan Jiujia Plastic Anti-corrosion Storage Tank is made of Rotomolding Special Material - Linear Low Density Polyethylene (LLDPE) or Linear Medium Density Polyethylene (LMDPE). It can hold most of the inorganic acids, alkalis, salts and many inorganic substances at room temperature.
2. The material used has a minimum softening point of 108 ° C and a maximum breaking point of -70 ° C, so it can generally be used for liquids with a temperature of -40 ° C to 60 ° C. If the temperature of the liquid is higher than 60 °C, a metal reinforcing sleeve should be arranged to prevent the tank from softening and deforming. If the tank is used for chemical reaction or dilution, the corresponding experiment should be carried out in advance to determine the maximum temperature of the reaction or dilution.
3. When you are not sure whether a substance can be contained, please refer to the Table of Chemical Properties of Polyethylene.
4. Install the basic requirements of the tank and be able to withstand the corresponding pressure, such as steel structure, the gap should not be too large, and should be covered with wood or iron.
5. When the storage tank is storing chemicals, there should be a good drainage ditch and dilution device around the site.
6. Since the tank is inevitably formed into a spherical crown when it is formed in the bottom of the tank, the foundation should be made into a spherical crown similar to the shape of the bottom. It is recommended to use a sand-like crown corresponding to the bottom of the tank on a horizontal basis. ).
7. Large-scale storage tanks should be safe when installing. Try to use cranes. Please contact us if you don't know the method.
8. When the plastic joint is tightened at the factory, the joint may loosen during transportation, loading and unloading. Therefore, the sealability of the joint should be checked before use. The liquid can be added to the joint to observe whether it leaks. Liquid storage tanks containing chemicals are best tested for leaks in water to prevent substantial losses.
9. The pipe connected to the lower joint or flange of the tank should be perpendicular to the wall of the tank. It is best to use a soft connection to avoid the uneven expansion of the upper and lower walls of the tank after the liquid is filled, resulting in leakage of the joint connection and damage to the joint and Bucket.
10. When the inlet port is higher from the bottom of the tank, the inlet port should be bent toward the tank wall to allow the incoming liquid to fall along the tank wall to reduce the impact on the bottom.
11. When installing a heavier accessory such as a mixer, or if the person has to work on the top of the tank and the top of the tank cannot bear the weight of the person, please make another shelf or ladder and pay attention to the safety of the work.
12. In the case where the liquid level cannot be controlled, an overflow port should be installed to prevent the liquid from overflowing from the manhole and cause unnecessary damage.
13. When the liquid inlet and discharge flow are large, the exhaust pipe of the corresponding flow rate should be installed.
14. Please contact our company again when changing the liquid.
15 If the tank is to be moved, use the steel plate to make the bottom and add the wheel underneath. It is best not to move.
Source Dongguan Jiujia Anticorrosive Equipment Co., Ltd. specializes in producing anti-corrosion plastic storage tanks, more plastic storage tanks information http://
Http://news.chinawj.com.cn Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn
G-Lights specialized in lighting design, lighting project construction, marketing and service. Focus on overseas lighting market business, including manufacturing indoor decorative high-end luxury Chandelier lighting and outdoor decoration lighting, outdoor solar lighting with paramount efficiency for minimum environment impact, Customized Building Facade Lighting, landscape lighting. Contribute to global sustainable development by designing. Won well reputation in main market such as Middle East, Europe, Asia, Africa and America. Excellent presentation in the world class lighting exhibitions, such as Frankfurt Light + Building, Hong Kong Lighting Fair, Guangzhou Lighting Fair, etc.
Chandelier pendant light,High Quality Chandelier pendant light,Chandelier pendant light Details, CN
ZHONGSHAN G-LIGHTS LIGHTING CO., LTD. , https://www.glightsled.com